Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The node pinctrl0 is already set up in the SOC DTSI files, but
defined again as member of pinctrl in most of the device DTS(I)
files. This patch removes this redundancy for the entire ramips
target.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts all remaining devices to use interrupt-driven
gpio-keys compatible instead of gpio-keys-polled.
The poll-interval is removed.
While at it, add/remove newlines in keys and leds node where
necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:
1. For the following devices, lan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The lan_mac statement is removed in 02_network, but
wan_mac is kept:
- mercury,mac1200r-v2
- phicomm,k2g
- skylab,skw92a
- wiznet,wizfi630a
2. For the following devices, wan_mac was set up with
mtd_get_mac_binary although the same address was set in DTS.
The wan_mac statement is removed in 02_network, no
lan_mac is present:
- buffalo,whr-g300n
- glinet,gl-mt300n-v2
- zyxel,keenetic-start
3. For the following device, lan_mac and wan_mac were set up
with mtd_get_mac_binary to the same address as set in DTS.
Both statements are removed in 02_network:
- buffalo,whr-600d
4. For some devices, it was possible to move setup from 02_network
to DTS by introducing previously missing mtd_mac_address:
- buffalo,whr-1166d
- buffalo,whr-300hp2
- buffalo,wsr-600dhp
- ohyeah,oy-0001
- planex,vr500
5. For one device, mtd_mac_address was just wrong and overwritten
by 02_network. Put the correct value in DTS and remove redundant
statement in 02_network:
- asus,rt-ac57u
6. For one device, MAC address defined in DTS is exchanged together
with lan_mac/wan_mac setup in 02_network, so that cases in
02_network can be merged:
- phicomm,k2p
For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo
Chuanhong Guo
Adrian Schmutzler