Bump kernel to 4.4.44. Compile-tested on ar71xx, ramips/mt7621 and x86/64.
.44 has been run-tested on the 17.01 branch here on ar71xx and mt7621.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:
[ 2.427349] hctosys: unable to open rtc device (rtc0)
[ 3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In dc92917 there was introduced login.sh wrapper which allows
configuration of console passwords via UCI system ttylogin config
option.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
commit a2386c384d requires the
module to be static in the kernel.
So lets actually add support for it inside the kernel config.
Tested on Ventana
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
* micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Point to correct devices when booting from msata or MMC
Changes fetched from Gateworks git
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Jo-Philipp Wich: rebased to apply against current LEDE version]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The image builder does not bundle sub-directories within $(KERNEL_BUILD_DIR),
therfore the intermediate "ventana-uImage.boot" directory is not shipped,
leading to failures with "make image" later on.
To circumvent the issue, store the intermediate boot files as tar archive
instead of putting them into a directory to ensure that they end up in the
final image builder tarball. Fixes FS#102
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix ubifs mkfs options
Use standard Build/* commands instead of doing everything in the hackish
ubi-boot-overlay template
Fix bootfs.tar.gz build error
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to create a bootable block storage device, both bootfs and rootfs
tarballs are required. However, our current scheme does not export a bootfs
tarball so add the packaging of it here.
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 49196
Change the name of the .ubi produced to strip out the word 'factory'. This is
mainly due to the fact that there is no difference between the Ventana 'factory'
image vs the standard image.
Name changes from:
openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to
openwrt-imx6-ventana-squashfs-nand_<size>.ubi
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48016
Some Ventana boards have a Marvell sky2 GigE controller as eth1 however
assigning the mac address through device-tree is difficult because the
PCI slot can move around depending on board configuration and slot population.
To work around this we add a patch to the sky2 driver to allow accessing its
mac address via a device-tree alias.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48013
On Ventana boards the Gateworks System Controller is the only device on I2C1
(/dev/i2c-0) and it can NAK transfers if it is busy in an ADC loop. Because
this is a multi-function device with several slave addresses it is best to
add retries at the controller level instead of within each slave driver. This
adds a patch that adds 3 retries for i2c transactions only for Ventana boards
and only for I2C1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48012
This is a backport of a2291badc355d58ead5c19ae0609468947416040 from thermal-soc
accepted upstream.
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP. Instead
of assuming 85C for passive cooling threshold and 100C for critical base
these thresholds off the thermal gade max CPU temperature:
- passive threshold: max - 10C
- critical threshold: max - 5C
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 48011
Certain board revisions of the GW52xx support an SPI host controller with
a single chip-select going to an off board connector.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48009
Koen Vandeputte
Stijn Segers
Petr Štetiar
Felix Fietkau
Álvaro Fernández Rojas
Mathias Kresin
Tim Harvey
Jo-Philipp Wich
Hauke Mehrtens
John Crispin
John Crispin
Luka Perkov
John Crispin
Felix Fietkau