The Cisco ON100 device is a Kirkwood based router:
SoC: Marvell 88F6282 1600Mhz
SDRAM memory: 512MB DDR3 1333Mhz
Gigabit ethernet: 2x Marvell 88E1310 (over RGMII)
Flash memory: 512MB
2 bi-colour status LEDs (green/red)
1 Reset button
1 USB 2.0 port (on back)
1 SDIO slot (on back)
This commit adds a target profile of "Cisco Systems ON100" under the target
system "Marvell Kirkwood".
Flashing can be performed over tftp, once "dhcp" has been issued:
tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin
nand erase 0x0c0000 ${filesize}
nand write ${loadaddr} 0x0c0000 ${filesize}
Once flashed, set environment variables to boot:
setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs
\; bootm
saveenv
Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
This patch add ZyXEL NSA325 2-Bay Media Server
The ZyXEL NSA325 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu
Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.
A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
The ZyXEL NSA310 device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: Realtek (over pcie)
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II port (1 internal and 1 external)
- 2 USB 2.0 ports (1 front and 1 back)
- Smart fan
The stock u-boot cannot read ubi so it should be replaced with the
LEDE/OpenWRT's u-boot or with a u-boot from here
https://github.com/mibodhi/u-boot-kirkwood
This device's boot ROM supports "kwboot" tool
(in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared)
that sends an uboot image to the board over serial connection, it is very easy to unbrick.
The stock bootloader can use usb and read from FAT filesystems,
so the installation process is simple, place the uboot file on a USB flashdrive
formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL
to the board and write the following commands in the bootloader console:
usb reset
fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin
nand write 0x1000000 0x00000 0x100000
reset
Now you are rebooting in the new u-boot, write this in its console to install the firmware:
usb reset
fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin
nand erase.part ubi
nand write 0x2000000 ubi 0x600000
If your firmware file is bigger than 6 MiBs you should write its size in hex
instead of 0x600000 above, or remove that number entirely (it will take a while in this case).
If you are using another uboot that can read ubi, set mtdparts like this
mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi)
And set your bootcmd to be like this
bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000
Then you can install the firmware as described above.
After you installed (or configured) the u-boot for booting the firmware,
write the device's mac address in the ethaddr u-boot env.
The MAC address is usually on a sticker under the device (one of the two codes is the serial),
it should begin with "107BEF" as it is assigned to ZyXEL.
write in the u-boot console (use your MAC address instead of the example)
setenv ethaddr 10:7B:EF:00:00:00
saveenv
to save the mac address in the u-boot.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Using pad-to instead of passing the optional padding to append-kernel
or append-rootfs. It could be that the value of a variable is passed.
In case the variable is empty no error is thrown.
Furthermore the purpose of the extra parameter is hard to get without
reading the code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Only add them where they are actually required.
Should help with compatibility issues with stock U-Boot images that
access UBI
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The new image requires `bootz` because of devicetree appending.
To flash a new image boot initramfs:
tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin
bootz 0x800000
# detach if already attached
ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
# scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp
ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin
# attach is important to resize rootfs_data otherwise it wont boot
ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}')
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49010
This is done with the new image generation system and board names.
It also generates a sysupgrade.tar image.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47432
It was wrong anyway, missing file sort order parameter which was fixed
in base month ago.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 47313
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
Support is added only for kernel 3.14 - do not show it until
the switch is made.
Following uboot env changes are needed to make it work on stock uboot:
Previous patch was pushed due to false user report. While at it fix alphabetic
ordering.
The board is optimized for ubi(fs) and boots OpenWrt without changes to uboot
environment if OpenWrt's uboot package is used. In order to flash the image run
following commands in uboot shell:
nand erase 0x200000 0x1fe00000
ubi part root ; ubi remove rootfs ; ubi create rootfs
tftpboot 0x800000 openwrt-kirkwood-iconnect-rootfs.ubifs ; ubi write 0x800000 rootfs ${filesize} ; reset
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39591
This patch adds the userland support for the Pogoplug E02 by Cloud
Engines, Inc.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 38631
* use lower case letters in generated images
* extend support for boot/ directory
* fix some typos
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 38629
Makoto Takeuchi
Alberto Bursi
Felix Fietkau
bobafetthotmail
Mathias Kresin
Jo-Philipp Wich
Ben Whitten
Luka Perkov
Felix Fietkau
Jonas Gorski
John Crispin