This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target seems to have been unmaintained for quite a while, and not a
single tester for the (now outdated) kernel 4.14 patches has been found.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for kernel 4.14 to the target and directly make it the
default kernel version to use.
This patch is build-tested only, but has never been device-tested. It is
only added to preserve the changes in Git history prior to removing this
target. Use it with care.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[rebased and extended commit message, refreshed patches for 4.14.162]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The configuration of the generic subtarget was used as the default
configuration and then the subtarget configurations were adapted.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device label shows the address currently assigned to the OpenWrt
LAN interface.
Current setup is:
LAN *:b8 factory 0xe006 label
WAN *:b7 factory 0xe000
For vendor FW bootlog we get (manually removed parts of the address):
[ 7.520000] set LAN/WAN LWLLL
[ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031
[ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7
[ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031
[ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8
[ 7.540000] eth1: ===> VirtualIF_open
Without further information, this does not allow verification of
the currently unexpected LAN/WAN assignment (we would expect 0xe000
to be LAN).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Refactor l2 freq scaling patch to support voltage
scaling and add support to base cache scaling on
cpu freq scaling. Update the dtsi files with the new
definition used in the new code.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
It's wrong set the mux to bias-disable. The best way to
do this is by creating a separate group and disable the
specific pins.
By documentation, any subgroup with no bias definition
is ignored so the mux definition is useless.
Rework the definition by sremoving the mux subgroup and
set the remaining subgroup with the mux function and
drive-strength
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The opp_notifier introduced with patch 0054-Handle-OPP-voltage adjust
for some reason missed the actual registration in the opp struct,
resulting in never being registred.
This was present in kernel 4.9 patchset but dropped in the transition
to 4.14. Reintroduce this and fix patch 0055 about L2 cache scaling.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Previous commit should have bumped PKG_RELEASE, but git add was
forgotten... Add it now.
Fixes: cd48d8d342 ("dnsmasq: switch to /tmp/resolv.conf.d/resolv.conf.auto")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mount-bind directory instead of resolv.conf.auto file in jail to
avoid problems when the file is deleted/replaced.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a backport from the dnsmasq master which should fix a bug which
could cause a crash in dnsmasq.
I saw the following crashes in my log:
[522413.117215] do_page_fault(): sending SIGSEGV to dnsmasq for invalid read access from 2a001450
[522413.124464] epc = 004197f1 in dnsmasq[400000+23000]
[522413.129459] ra = 004197ef in dnsmasq[400000+23000]
This is happening in blockdata_write() when block->next is
dereferenced, but I am not sure if this is related to this problem or if
this is a different problem. I am unable to reproduce this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address on the label of this device corresponds to the
2.4 GHz and ethernet MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add call to fclose for file pointer fp in function t_openpw.
The resource leak could happen during an error handling.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
78cd384 Update README and patchlevel.h for 2.4.8 release
5d03403 pppd: Avoid use of strnlen (and strlen) in vslprintf
a1e950a pppd: Fix IPv6 default route code for Solaris
ca5e61b plugins/rp-pppoe: Make tag parsing loop condition more accurate
c10c3c7 pppd: Make sure word read from options file is null-terminated
b311e98 pppd: Limit memory accessed by string formats with max length specified
3ea9de9 pppd: Eliminate some more compiler warnings
57edb1a pppd: Include time.h header before using time_t
09f695f pppd: Don't free static string
03104ba pppd.h: Add missing headers
388597e pppd: Add defaultroute6 and related options
66ce4ba pppd: Avoid declarations within statements in main.c
5637180 pppd: Fix `ifname` option in case of multilink (#105)
d00f8a0 pppd: Fix variable reference syntax in Makefile.linux
b6b4d28 pppd: Check tdb pointer before closing
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
If CONFIG_DROPBEAR_ZLIB is set, building fails at the packaging stage
due to an undeclared dependency on libz.so.1.
As is already done for the main dropbear package, conditionally add a
dependency on zlib.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
It seems the buildbots can't handle it.
Added a cmake option to find the cxxabi files as they are part of the
toolchain and not in the normal path. It doesn't seem to make a
difference, just gets rid of cmake warnings.
Added another small GCC warning fix. It's fairly minor.
This has no change in compiled size, and most likely no change in
behavior. Bumped the PKG_RELEASE anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
ddc11c3932
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
These two hacks are no longer necessary as they've
been moved to a special variant of kmod-ath10k-ct.
So, if you have a device suffering from low-memory
situation and getting applications crashes due to
the OOM reaper or kernel panics with ath10k, please
use the "kmod-ath10k-ct-smallbuffers" package from
now on.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adrian Schmutzler
Hauke Mehrtens
Álvaro Fernández Rojas
Ansuel Smith
Matthias Schiffer
Daniel Golle
Yong-hyu Ban
Jack Chen
Andrea Dalla Costa
Mason Clarke
DENG Qingfang
Matt Merhar
Christoph Krapp
Rosen Penev
Bjørn Mork
Josef Schlehofer
Tokunori Ikegami
Christian Lamparter
Jo-Philipp Wich
Petr Štetiar