This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.
Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board
Installation:
* Flashing through the OEM web interface:
+ Connect your computer to the router with an ethernet cable and browse
to http://192.168.0.51/
+ Log in with the default credentials are admin:password
+ Browse to Advanced > Administration > Firmware Upgrade in the Telenet
interface
+ Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
+ Proceed with the firmware installation and give the device a few
minutes to finish and reboot.
* Flashing through TFTP:
+ Configure your wired client with a static IP in the 192.168.1.x range,
e.g. 192.168.1.10 and netmask 255.255.255.0.
+ Power off the router.
+ Press and hold the RESET button (the factory reset button on the bottom
of the device, with the gray circle around it, next to the Telenet logo)
and turn the router on while keeping the button pressed.
+ The power LED will start flashing orange. You can release the button
once it switches to flashing green.
+ Transfer the image over TFTP:
$ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Change the caldata partition DTS node label to be consistent with
the label property for some Netgear WNDR devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Davy Hollevoet
Adrian Schmutzler
Michal Cieslakiewicz