The user can now enable the ACK timeout estimation algorithm (dynack)
for drivers that support it.
It is also expected that the distance config accepts the same values as:
$ iw phyX set distance XXX
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Most work was done in commit 021c893658 ("ramips: fix size-cells on spi
nodes"), but a few more DTS files using the old reg style have been added
since then. This commit fixes them.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.
However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Use same indent as for the rest of the file.
Signed-off-by: Javier Marcet <javier@marcet.info>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Out of all devices currently supported based on AR9331 chipset,
this one had the 'serial0' alias missing. Add it to fix setting of
/dev/console and login shell on the onboard UART.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
- use tab indent in image build recipes for consistency
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As the node is already defined and labeled in SoC DTSI file, we can refer to it
outside of root node and reduce redundancy.
While at it, remove unused pcf8563 label.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Fixes a build error seen when applying the kernel patches.
Applying patch generic/435-mtd-add-routerbootpart-parser-config.patch
patching file drivers/mtd/parsers/Kconfig
Hunk #1 FAILED at 160.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Kconfig
patching file drivers/mtd/parsers/Makefile
Hunk #1 FAILED at 10.
1 out of 1 hunk FAILED -- rejects in file drivers/mtd/parsers/Makefile
This was missed as 5.4 is currently set as testing kernel
while the main kernel being used is 4.19
Fixes: 2976e423dc ("generic: routerboot partition build bits")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This commit takes advantages of base-files 220 which introduces routines
to perform caldata loading directly via the kernel sysfs loader helper.
This has the benefits of not wasting flash space to store caldata.
Memory footprint is reduced to the bare minimum: for devices that don't
need MAC patching, the caldata is loaded directly, for devices that do
need MAC patching, the caldata is extracted to /tmp, patched and then
loaded.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This will enable platforms to extract caldata to an arbitrary file,
or patch mac in an abitrary file.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Rationale:
1/ This tool is no longer necessary following the implementation of a
sysfs driver
2/ The upstream author, Robert Marko, stated[1] that this tool had been
taken from his tree in an unfinished state not suitable for merging
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610277863
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
With the implementation of a sysfs interface to access WLAN data, this
target no longer needs a special wrapper to extract caldata.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
To match sticker and vendor OS behavior, WAN MAC is set to the device
base MAC and LAN MAC is incremented from that.
Note: this will trigger a harmless kernel message during boot:
ag71xx 19000000.eth: invalid MAC address, using random address
There is no clean workaround to prevent this message from being emitted.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Some newer MikroTik RouterBOARD devices use a new encoding scheme
for their WLAN calibration data. This patch provides support for
decoding this new scheme.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver exposes the data encoded in the "hard_config" flash segment
of MikroTik RouterBOARDs devices. It presents the data in a sysfs folder
named "hard_config". The WLAN calibration data is available on demand via
the 'wlan_data' sysfs file in that folder.
This driver permanently allocates a chunk of RAM as large as the
"hard_config" MTD partition (typically 4KB), although it is technically
possible to operate entirely from the MTD device without using a local
buffer (except when requesting WLAN calibration data), at the cost of a
performance penalty.
This driver does not reuse any of the existing code previously found in
routerboot.c.
This driver has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This driver provides an OF MTD parser to properly assign the RouterBoot
partitions on the flash. This parser builds from the "fixed-partitions"
one (see ofpart.c), but it can handle dynamic partitions as found on
routerboot devices.
The parent node must contain the following:
compatible = "mikrotik,routerboot-partitions";
#address-cells = <1>;
#size-cells = <1>;
Children routerbootpart DTS nodes are defined as follows:
For fixed partitions
node-name@unit-address {
reg = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
All properties but reg are optional.
For dynamic partitions:
node-name {
size = <prop-encoded-array>;
label = <string>;
read-only;
lock;
};
size property is mandatory unless the next partition is a fixed one or
a "well-known" one (matched from the strings defined below) in which case
it can be omitted or set to 0; other properties are optional.
By default dynamic partitions are appended after the preceding one, except
for "well-known" ones which are automatically located on flash.
Well-known partitions (matched via label or node-name):
- "hard_config"
- "soft_config"
- "dtb_config"
This parser requires the DTS to list partitions in ascending order as
expected on the MTD device.
This parser has been successfully tested on BE (ath79) and LE (ipq40xx
and ramips) hardware.
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Christopher Hill <ch6574@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
add option to set management IP pattern
also add missing 'unconfigure system hostname'
for example pattern '!192.168.1.1' makes it possible that
WAN IP is selected instead of LAN IP
Signed-off-by: Daniel A. Maierhofer <git@damadmai.at>
[grammar and spelling fixes in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Samba 3.6 is completely unsupported, in addition to having tons of patches
It also causes kernel panics on some platforms when sendfile is enabled.
Example:
https://github.com/gnubee-git/GnuBee_Docs/issues/45
I have reproduced on ramips as well as mvebu in the past.
Samba 4 is an alternative available in the packages repo.
cifsd is a lightweight alternative available in the packages repo. It is
also a faster alternative to both Samba versions (lower CPU usage). It
was renamed to ksmbd.
To summarize, here are the alternatives:
- ksmbd + luci-app-cifsd
- samba4 + luci-app-samba4
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[drop samba36-server from GEMINI_NAS_PACKAGES, ksmbd rename + summary]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-dpl with only one package
installing all 4 files as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain ls-mc with only one package
installing all two images as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's installing.
It is easier to maintain fman-ucode with only one package
installing all two binaries as intermediate files.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Update tfa package to latest LSDK-20.04 dropping one patch
which had already been integrated.
Add fixes,
- Fix DEPENDS/PKG_BUILD_DEPENDS.
- Remove HIDDEN:=1.
- Move intermediate files installing into Build/InstallDev.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Update u-boot package to latest LSDK-20.04 dropping patches
which are no longer needed.
Adapt u-boot bootargs to kernel 5.4 for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Update ls-rcw to latest LSDK-20.04.
Update patch 0001 with a new one.
Drop patch 0002 since it had been integrated.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The Freescale IFC NAND/NOR controllers options were disabled
in default in previous running make kernel_oldconfig.
So re-enable them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Ali MJ Al-Nasrawy
Sungbo Eo
Jakov Petrina
Javier Marcet
Lech Perczak
Koen Vandeputte
Thibaut VARÈNE
Stijn Tintel
Daniel A. Maierhofer
Rosen Penev
Jo-Philipp Wich
Yangbo Lu