ath79: add support for OCEDO Koala
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
v19.07.3_mercusys_ac12_duma
David Bauer
6 years ago
committed by
Mathias Kresin
parent
387736af41
commit
c4931713df
@ -0,0 +1,169 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca9557.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "ocedo,koala", "qca,qca9557";
|
||||
model = "OCEDO Koala";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-status = &system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power {
|
||||
label = "koala:green:power";
|
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
wifi2 {
|
||||
label = "koala:yellow:wlan2";
|
||||
gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wifi5 {
|
||||
label = "koala:red:wlan58";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
system: system {
|
||||
label = "koala:blue:sys";
|
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <100>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pll {
|
||||
clocks = <&extosc>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x040000 0x010000>;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x050000 0x740000>;
|
||||
};
|
||||
|
||||
partition@790000 {
|
||||
label = "vendor";
|
||||
reg = <0x790000 0x740000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ed0000 {
|
||||
label = "data";
|
||||
reg = <0xed0000 0x110000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "id";
|
||||
reg = <0xfe0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@ff0000 {
|
||||
label = "art";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&art 0x06>;
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
|
||||
phy5: ethernet-phy@5 {
|
||||
reg = <5>;
|
||||
phy-mode = "rgmii-rxid";
|
||||
|
||||
at803x-disable-smarteee;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&art 0x00>;
|
||||
|
||||
phy-handle = <&phy5>;
|
||||
phy-mode = "rgmii-rxid";
|
||||
|
||||
pll-data = <0xae000000 0xa0000101 0xa0001313>;
|
||||
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
|
||||
rxdv-delay = <3>;
|
||||
rxd-delay = <3>;
|
||||
txen-delay = <0>;
|
||||
txd-delay = <0>;
|
||||
rgmii-enabled = <1>;
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue