ath79: add support for Qihoo C301
Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>master
parent
fae125781e
commit
a9360452f0
@ -0,0 +1,11 @@
|
||||
#!/bin/sh /etc/rc.common
|
||||
START=99
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
qihoo,c301)
|
||||
local n=$(fw_printenv activeregion | cut -d = -f 2)
|
||||
fw_setenv "image${n}trynum" 0
|
||||
;;
|
||||
esac
|
||||
}
|
@ -0,0 +1,236 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Qihoo 360 C301";
|
||||
compatible = "qihoo,c301";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_wlan_g;
|
||||
led-failsafe = &led_wlan_o;
|
||||
led-upgrade = &led_wlan_o;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
led_wlan_g: wlan_g {
|
||||
label = "c301:green:wlan";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan_o: wlan_o {
|
||||
label = "c301:orange:wlan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
reg_eth_led_vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "eth_led_vbus";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
reg_usb_vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
pmx_spi_cs1: pinmux_spi_cs1 {
|
||||
pinctrl-single,bits = <0xc 0x07 0xff>;
|
||||
};
|
||||
|
||||
pmx_led_switch: pinmux_led_switch {
|
||||
pinctrl-single,bits = <0x0 0x2b2a2d00 0xffffff00>;
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
|
||||
gpio_ext_lna0 {
|
||||
gpio-hog;
|
||||
gpios = <14 0>;
|
||||
output-high;
|
||||
line-name = "c301:ext:lna0";
|
||||
};
|
||||
|
||||
gpio_ext_lna1 {
|
||||
gpio-hog;
|
||||
gpios = <15 0>;
|
||||
output-high;
|
||||
line-name = "c301:ext:lna1";
|
||||
};
|
||||
};
|
||||
|
||||
&builtin_switch {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_led_switch>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_spi_cs1>;
|
||||
status = "okay";
|
||||
|
||||
num-cs = <2>;
|
||||
cs-gpios= <0>, <0>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "devdata";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "devconf";
|
||||
reg = <0x60000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "seama";
|
||||
label = "firmware";
|
||||
reg = <0x70000 0xf60000>;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "warm_start";
|
||||
reg = <0xfd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "action_image_config";
|
||||
reg = <0xfe0000 0x10000>;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "radiocfg";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "firmware2";
|
||||
reg = <0x0 0xf00000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
label = "privatedata";
|
||||
reg = <0xf00000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
switch-phy-swap = <1>;
|
||||
switch-only-mode = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
phy-handle = <&swphy0>;
|
||||
};
|
Loading…
Reference in New Issue