ath79: add support for Comfast CF-EW72
Specifications: Qualcomm/Atheros QCA9531 + QCA9886 2x 10/100 Mbps Ethernet, with 48v PoE 2T2R 2.4 GHz, 802.11b/g/n 2T2R 5 GHz, 802.11a/n/ac 128MB RAM 16MB SPI Flash 4x LED (Always On Power, LAN, WAN, WLAN) Flashing Instructions: Original firmware is based on OpenWRT, so flashing the sysupgrade image on the factory firmware is sufficient. Tested: Reset button, WAN LED, LAN LED, Power LED (always on, not much to test), WLAN LED (one LED only for 2 interfaces, by default it gets assigned to the first interface), MAC addresses (match factory firmware). My LAN factory MAC address ends in F2. use stock_mac art_loc lan :f2 0x0 wan :f3 0x1002 5g :f4 0x6 2g :f5 0x5006 Since MAC address flash locations do not really match their use in vendor firmware (e.g. address from 5 GHz calibration data is assigned to 2.4 GHz WiFi), just calculate the MAC addresses with an offset based on 0x0 address. Signed-off-by: Chris Morgan <macromorgan@hotmail.com> [add MAC address comment] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>master
parent
ae06a650d6
commit
7daab62861
@ -0,0 +1,132 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "qca953x.dtsi"
|
||||
|
||||
/ {
|
||||
compatible = "comfast,cf-ew72", "qca,qca9531";
|
||||
model = "COMFAST CF-EW72";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart;
|
||||
led-boot = &led_wan;
|
||||
led-failsafe = &led_wan;
|
||||
led-upgrade = &led_wan;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
lan {
|
||||
label = "cf-ew72:blue:lan";
|
||||
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wan: wan {
|
||||
label = "cf-ew72:blue:wan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "cf-ew72:blue:wlan";
|
||||
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
watchdog {
|
||||
compatible = "linux,wdt-gpio";
|
||||
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
hw_algo = "toggle";
|
||||
hw_margin_ms = <1200>;
|
||||
always-running;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
status = "okay";
|
||||
|
||||
num-cs = <1>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "winbond,w25q128", "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@10000 {
|
||||
label = "art";
|
||||
reg = <0x010000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
compatible = "denx,uimage";
|
||||
label = "firmware";
|
||||
reg = <0x020000 0xfd0000>;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "nvram";
|
||||
reg = <0xff0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
phy-handle = <&swphy4>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
mtd-mac-address-increment = <1>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&art 0x0>;
|
||||
mtd-mac-address-increment = <3>;
|
||||
};
|
Loading…
Reference in New Issue