ath79: add support for NEC Aterm WG1200CR

NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
v19.07.3_mercusys_ac12_duma
INAGAKI Hiroshi 5 years ago committed by Christian Lamparter
parent fac27643f0
commit 643fcfc8d6

@ -128,6 +128,13 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "5:wan" "6@eth1" "4:lan"
;;
nec,wg1200cr|\
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
nec,wg800hp)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
@ -234,12 +241,6 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "5:lan" "1:wan"
;;
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
xiaomi,mi-router-4q)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
@ -272,7 +273,8 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "mac" 4)
wan_mac=$(mtd_get_mac_text "mac" 24)
;;
dlink,dir-859-a1)
dlink,dir-859-a1|\
nec,wg1200cr)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
;;

@ -117,6 +117,10 @@ case "$FIRMWARE" in
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2
;;
nec,wg1200cr)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata wlan24mac) 2
;;
nec,wg800hp)
ath9k_eeprom_extract "art" 4096 1088
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2

@ -163,6 +163,12 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
nec,wg1200cr)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")

@ -0,0 +1,176 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca956x.dtsi"
/ {
model = "NEC Aterm WG1200CR";
compatible = "nec,wg1200cr", "qca,qca9563";
chosen {
bootargs = "console=ttyS0,115200n8";
};
aliases {
led-boot = &power_green;
led-failsafe = &power_red;
led-running = &power_green;
led-upgrade = &power_green;
};
leds {
compatible = "gpio-leds";
/* other LEDs are connected to ath10k (QCA9888) gpiochip */
power_green: power_green {
label = "wg1200cr:green:power";
gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
default-state = "on";
};
power_red: power_red {
label = "wg1200cr:red:power";
gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys";
reset {
label = "reset";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
wps {
label = "wps";
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
debounce-interval = <60>;
};
bridge {
label = "br";
gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
converter {
label = "cnv";
gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "devdata";
reg = <0x040000 0x010000>;
read-only;
};
partition@50000 {
label = "devconf";
reg = <0x050000 0x010000>;
read-only;
};
partition@60000 {
label = "misc";
reg = <0x060000 0x010000>;
read-only;
};
partition@70000 {
label = "wifimngdata";
reg = <0x070000 0x010000>;
read-only;
};
partition@80000 {
compatible = "seama";
label = "firmware";
reg = <0x080000 0x770000>;
};
partition@7f0000 {
label = "art";
reg = <0x7f0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
0x04 0x00000080 /* PORT0 PAD MODE CTRL */
0x50 0xcc35cc35 /* LED_CTRL0 */
0x54 0xca35ca35 /* LED_CTRL1 */
0x58 0xc935c935 /* LED_CTRL2 */
0x5c 0x03ffff00 /* LED_CTRL3 */
0x7c 0x0000007e /* PORT0_STATUS */
>;
};
};
&eth0 {
status = "okay";
pll-data = <0x03000101 0x00000101 0x00001919>;
phy-mode = "sgmii";
phy-handle = <&phy0>;
};
&pcie {
status = "okay";
wifi@0,0 {
compatible = "pci168c,0056";
reg = <0x0000 0 0 0 0>;
};
};
&uart {
status = "okay";
};
&wmac {
status = "okay";
qca,no-eeprom;
};

@ -42,6 +42,12 @@ define Build/add-elecom-factory-initramfs
fi
endef
define Build/nec-enc
$(STAGING_DIR_HOST)/bin/nec-enc \
-i $@ -o $@.new -k $(1)
mv $@.new $@
endef
define Build/nec-fw
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
( \
@ -446,6 +452,24 @@ define Device/librerouter_librerouter-v1
endef
TARGET_DEVICES += librerouter_librerouter-v1
define Device/nec_wg1200cr
ATH_SOC := qca9563
DEVICE_TITLE := NEC Aterm WG1200CR
IMAGE_SIZE := 7616k
SEAMA_MTDBLOCK := 6
SEAMA_SIGNATURE := wrgac72_necpf.2016gui_wg1200cr
IMAGES += factory.bin
IMAGE/default := \
append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := \
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | nec-enc 9gsiy9nzep452pad | \
check-size $$$$(IMAGE_SIZE)
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
endef
TARGET_DEVICES += nec_wg1200cr
define Device/nec_wg800hp
ATH_SOC := qca9563
DEVICE_TITLE := NEC Aterm WG800HP

Loading…
Cancel
Save