kernel: Fix ath79 DSP exception at bootup

This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.

Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
master
Hauke Mehrtens 4 years ago
parent 3b0f698760
commit 4bb5e331a7

@ -0,0 +1,61 @@
From db4603e30effd74d4adb6bcdf73072b2c06fafcd Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Fri, 3 Jul 2020 00:07:15 +0200
Subject: [PATCH] MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:
[ 0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.107070] Kernel panic - not syncing: Unexpected DSP exception
[ 0.113470] Rebooting in 1 seconds..
We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.
In the kernel I bisected this problem to commit 9012d011660e ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c34b ("MIPS: Always
allocate exception vector for MIPSr2+").
Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: <stable@vger.kernel.org>
---
arch/mips/kernel/traps.c | 1 +
1 file changed, 1 insertion(+)
--- a/arch/mips/kernel/traps.c
+++ b/arch/mips/kernel/traps.c
@@ -2096,6 +2096,7 @@ static void configure_status(void)
change_c0_status(ST0_CU|ST0_MX|ST0_RE|ST0_FR|ST0_BEV|ST0_TS|ST0_KX|ST0_SX|ST0_UX,
status_set);
+ back_to_back_c0_hazard();
}
unsigned int hwrena;

@ -0,0 +1,61 @@
From db4603e30effd74d4adb6bcdf73072b2c06fafcd Mon Sep 17 00:00:00 2001
From: Hauke Mehrtens <hauke@hauke-m.de>
Date: Fri, 3 Jul 2020 00:07:15 +0200
Subject: [PATCH] MIPS: Add missing EHB in mtc0 -> mfc0 sequence for DSPen
This resolves the hazard between the mtc0 in the change_c0_status() and
the mfc0 in configure_exception_vector(). Without resolving this hazard
configure_exception_vector() could read an old value and would restore
this old value again. This would revert the changes change_c0_status()
did. I checked this by printing out the read_c0_status() at the end of
per_cpu_trap_init() and the ST0_MX is not set without this patch.
The hazard is documented in the MIPS Architecture Reference Manual Vol.
III: MIPS32/microMIPS32 Privileged Resource Architecture (MD00088), rev
6.03 table 8.1 which includes:
Producer | Consumer | Hazard
----------|----------|----------------------------
mtc0 | mfc0 | any coprocessor 0 register
I saw this hazard on an Atheros AR9344 rev 2 SoC with a MIPS 74Kc CPU.
There the change_c0_status() function would activate the DSPen by
setting ST0_MX in the c0_status register. This was reverted and then the
system got a DSP exception when the DSP registers were saved in
save_dsp() in the first process switch. The crash looks like this:
[ 0.089999] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.097796] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.107070] Kernel panic - not syncing: Unexpected DSP exception
[ 0.113470] Rebooting in 1 seconds..
We saw this problem in OpenWrt only on the MIPS 74Kc based Atheros SoCs,
not on the 24Kc based SoCs. We only saw it with kernel 5.4 not with
kernel 4.19, in addition we had to use GCC 8.4 or 9.X, with GCC 8.3 it
did not happen.
In the kernel I bisected this problem to commit 9012d011660e ("compiler:
allow all arches to enable CONFIG_OPTIMIZE_INLINING"), but when this was
reverted it also happened after commit 172dcd935c34b ("MIPS: Always
allocate exception vector for MIPSr2+").
Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
does similar changes to a different file. I am not sure if there are
more places affected by this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: <stable@vger.kernel.org>
---
arch/mips/kernel/traps.c | 1 +
1 file changed, 1 insertion(+)
--- a/arch/mips/kernel/traps.c
+++ b/arch/mips/kernel/traps.c
@@ -2126,6 +2126,7 @@ static void configure_status(void)
change_c0_status(ST0_CU|ST0_MX|ST0_RE|ST0_FR|ST0_BEV|ST0_TS|ST0_KX|ST0_SX|ST0_UX,
status_set);
+ back_to_back_c0_hazard();
}
unsigned int hwrena;
Loading…
Cancel
Save