ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
master
Yanase Yuki
4 years ago
committed by
Petr Štetiar
parent
d2c3131b3f
commit
4a77a060ab
Binary file not shown.
Binary file not shown.
@ -0,0 +1,419 @@
|
||||
// SPDX-License-Identifier: ISC
|
||||
/*
|
||||
* Copyright (c) 2015 - 2016, The Linux Foundation. All rights reserved.
|
||||
* Copyright (c) 2020 Yanase Yuki <dev@zpc.sakura.ne.jp>
|
||||
*/
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
|
||||
/ {
|
||||
model = "Buffalo WTR-M2133HP";
|
||||
compatible = "buffalo,wtr-m2133hp", "qcom,ipq4019";
|
||||
|
||||
memory {
|
||||
device_type = "memory";
|
||||
reg = <0x80000000 0x20000000>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
/*
|
||||
* U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs" to
|
||||
* kernel command line. But we use different partition names,
|
||||
* so we have to set correct parameters.
|
||||
*/
|
||||
bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_orange;
|
||||
led-running = &led_power_white;
|
||||
led-upgrade = &led_power_blue;
|
||||
label-mac-device = &gmac0;
|
||||
};
|
||||
|
||||
soc {
|
||||
rng@22000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
|
||||
crypto@8e3a000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
watchdog@b017000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ess-switch@c000000 {
|
||||
status = "okay";
|
||||
switch_lan_bmp = <0x1c>;
|
||||
};
|
||||
|
||||
ess-psgmii@98000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
edma@c080000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
usb3@8af8800 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power_white: power_white {
|
||||
label = "wtr-m2133hp:white:power";
|
||||
gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_power_orange: power_orange {
|
||||
label = "wtr-m2133hp:orange:power";
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_power_blue: power_blue {
|
||||
label = "wtr-m2133hp:blue:power";
|
||||
gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_white {
|
||||
label = "wtr-m2133hp:white:router";
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_orange {
|
||||
label = "wtr-m2133hp:orange:router";
|
||||
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_white {
|
||||
label = "wtr-m2133hp:white:internet";
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_orange {
|
||||
label = "wtr-m2133hp:orange:internet";
|
||||
gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_white {
|
||||
label = "wtr-m2133hp:white:wireless";
|
||||
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_orange {
|
||||
label = "wtr-m2133hp:orange:wireless";
|
||||
gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
auto_mode {
|
||||
label = "auto_mode";
|
||||
gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
router_mode {
|
||||
label = "router_mode";
|
||||
gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
ap_mode {
|
||||
label = "ap_mode";
|
||||
gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_2>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "AOSS Button";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
serial_0_pins: serial0_pinmux {
|
||||
mux {
|
||||
pins = "gpio16", "gpio17";
|
||||
function = "blsp_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
mdio_pins: mdio_pinmux {
|
||||
mux_1 {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_2 {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
pullups {
|
||||
pins = "gpio52", "gpio53", "gpio58",
|
||||
"gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
usb_power {
|
||||
line-name = "USB power";
|
||||
gpios = <34 GPIO_ACTIVE_HIGH>;
|
||||
gpio-hog;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
bridge@0,0 {
|
||||
reg = <0x00000000 0 0 0 0>;
|
||||
#address-cells = <3>;
|
||||
#size-cells = <2>;
|
||||
ranges;
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0 0 0 0 0>;
|
||||
|
||||
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0000000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x0100000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "BOOTCONFIG";
|
||||
reg = <0x0200000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "QSEE";
|
||||
reg = <0x0300000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "QSEE_1";
|
||||
reg = <0x0400000 0x0100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
label = "CDT";
|
||||
reg = <0x0500000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "CDT_1";
|
||||
reg = <0x0580000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "BOOTCONFIG1";
|
||||
reg = <0x0600000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x0680000 0x0080000>;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x0700000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "APPSBL_1";
|
||||
reg = <0x0900000 0x0200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@b00000 {
|
||||
label = "ART";
|
||||
reg = <0x0b00000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b80000 {
|
||||
label = "ART_1";
|
||||
reg = <0x0b80000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
orgdata: partition@c00000 {
|
||||
label = "ORGDATA";
|
||||
reg = <0x0c00000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c80000 {
|
||||
label = "ORGDATA_1";
|
||||
reg = <0x0c80000 0x0080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d00000 {
|
||||
label = "ubi";
|
||||
reg = <0x0d00000 0x2900000>;
|
||||
};
|
||||
|
||||
partition@3600000 {
|
||||
label = "rootfs_recover";
|
||||
reg = <0x3600000 0x2900000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@5f00000 {
|
||||
label = "user_property";
|
||||
reg = <0x5f00000 0x1a20000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
|
||||
ieee80211-freq-limit = <2400000 2483000>;
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&gmac0 {
|
||||
mtd-mac-address = <&orgdata 0x20>;
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
mtd-mac-address = <&orgdata 0x20>;
|
||||
};
|
||||
|
||||
&usb3_ss_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_hs_phy {
|
||||
status = "okay";
|
||||
};
|
||||
Loading…
Reference in New Issue