ath79: add support for D-Link DAP-1330/DAP-1365 A1

Port device support for DAP-1330 from the ar71xx target to ath79.

Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.

Specifications:

 * QCA9533, 8 MiB Flash, 64 MiB RAM
 * One Ethernet Port (10/100)
 * Wall-plug style case (DAP-1365 with additional socket)
 * LED bargraph RSSI indicator

Installation:

 * Web UI: http://192.168.0.50 (or different address obtained via DHCP)
   There is no password set by default
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.50
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
     http://192.168.0.50/cgi/index

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
master
Sebastian Schaper 4 years ago committed by Petr Štetiar
parent 358aec7775
commit 361c670a46

@ -0,0 +1,9 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qca9533_dlink_dap-13xx.dtsi"
/ {
compatible = "dlink,dap-1330-a1", "qca,qca9533";
model = "D-Link DAP-1330 A1";
};

@ -0,0 +1,9 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "qca9533_dlink_dap-13xx.dtsi"
/ {
compatible = "dlink,dap-1365-a1", "qca,qca9533";
model = "D-Link DAP-1365 A1";
};

@ -0,0 +1,127 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca953x.dtsi"
/ {
aliases {
led-boot = &led_power;
led-failsafe = &led_status;
led-running = &led_power;
led-upgrade = &led_status;
};
keys {
compatible = "gpio-keys";
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
};
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "d-link:green:power";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
};
led_status: status {
label = "d-link:red:status";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
rssilow {
label = "d-link:red:rssilow";
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
};
rssimediumlow {
label = "d-link:green:rssimediumlow";
gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
};
rssimediumhigh {
label = "d-link:green:rssimediumhigh";
gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
};
rssihigh {
label = "d-link:green:rssihigh";
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x10000>;
read-only;
};
art: partition@10000 {
label = "art";
reg = <0x10000 0x10000>;
read-only;
};
partition@20000 {
label = "mp";
reg = <0x20000 0x10000>;
read-only;
};
partition@30000 {
label = "config";
reg = <0x30000 0x10000>;
read-only;
};
partition@40000 {
label = "firmware";
reg = <0x40000 0x7c0000>;
compatible = "denx,uimage";
};
};
};
};
&uart {
status = "okay";
};
&eth0 {
status = "okay";
};
&wmac {
status = "okay";
mtd-cal-data = <&art 0x1000>;
};

@ -132,6 +132,14 @@ compex,wpj531-16m)
devolo,magic-2-wifi)
ucidef_set_led_netdev "plcw" "dLAN" "devolo:white:dlan" "eth0.1" "rx"
;;
dlink,dap-1330-a1|\
dlink,dap-1365-a1)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_led_rssi "rssilow" "RSSILOW" "d-link:red:rssilow" "wlan0" "1" "25"
ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "d-link:green:rssimediumlow" "wlan0" "1" "100"
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "d-link:green:rssimediumhigh" "wlan0" "51" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "d-link:green:rssihigh" "wlan0" "76" "100"
;;
dlink,dir-859-a1)
ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20"
;;

@ -23,6 +23,8 @@ ath79_setup_interfaces()
devolo,dvl1750c|\
devolo,dvl1750i|\
devolo,dvl1750x|\
dlink,dap-1330-a1|\
dlink,dap-1365-a1|\
dlink,dir-505|\
engenius,ecb1750|\
enterasys,ws-ap3705i|\
@ -386,13 +388,15 @@ ath79_setup_macs()
devolo,magic-2-wifi)
label_mac=$(macaddr_add "$(mtd_get_mac_binary art 0x1002)" 3)
;;
dlink,dap-2695-a1)
label_mac=$(mtd_get_mac_ascii bdcfg "wlanmac")
;;
dlink,dap-1330-a1|\
dlink,dap-1365-a1|\
dlink,dch-g020-a1)
lan_mac=$(mtd_get_mac_text "mp" 0x1)
label_mac=$lan_mac
;;
dlink,dap-2695-a1)
label_mac=$(mtd_get_mac_ascii bdcfg "wlanmac")
;;
dlink,dir-825-b1)
lan_mac=$(mtd_get_mac_text "caldata" 0xffa0)
wan_mac=$(mtd_get_mac_text "caldata" 0xffb4)

@ -17,6 +17,8 @@ case "$board" in
adtran,bsap1840)
macaddr_add "$(mtd_get_mac_binary 'Board data' 2)" $(($PHYNBR * 8 + 1)) > /sys${DEVPATH}/macaddress
;;
dlink,dap-1330-a1|\
dlink,dap-1365-a1|\
dlink,dch-g020-a1)
mtd_get_mac_text "mp" 0x13 > /sys${DEVPATH}/macaddress
;;

@ -8,6 +8,13 @@ case "$board" in
arduino,yun)
migrate_leds "arduino:=yun:"
;;
dlink,dap-1330-a1)
migrate_leds ":red:power=:red:status" \
":red:wifi=:red:rssilow" \
":green:wifi=:green:rssimediumlow" \
":green:signal1=:green:rssimediumhigh" \
":green:signal2=:green:rssihigh"
;;
engenius,epg5000)
migrate_leds ":wlan-2g=:wlan2g" ":wlan-5g=:wlan5g"
;;

@ -565,6 +565,33 @@ define Device/devolo_magic-2-wifi
endef
TARGET_DEVICES += devolo_magic-2-wifi
define Device/dlink_dap-13xx
SOC := qca9533
DEVICE_VENDOR := D-Link
DEVICE_PACKAGES += rssileds
IMAGE_SIZE := 7936k
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
append-rootfs | pad-rootfs | check-size | mkdapimg2 0xE0000
endef
define Device/dlink_dap-1330-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1330
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1330
SUPPORTED_DEVICES += dap-1330-a1
endef
TARGET_DEVICES += dlink_dap-1330-a1
define Device/dlink_dap-1365-a1
$(Device/dlink_dap-13xx)
DEVICE_MODEL := DAP-1365
DEVICE_VARIANT := A1
DAP_SIGNATURE := HONEYBEE-FIRMWARE-DAP-1365
endef
TARGET_DEVICES += dlink_dap-1365-a1
define Device/dlink_dap-2695-a1
SOC := qca9558
DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct

Loading…
Cancel
Save