dumalogiya
/
openwrt
2
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
v19.07.3_mercusys_ac12_duma
master
Branches Tags
${ item.name }
Create tag ${ searchTerm }
Create branch ${ searchTerm }
from 'd3f82d3b84'
${ noResults }
openwrt/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files....

40 lines
1.2 KiB
Diff
Raw Normal View History Unescape Escape

ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
6 years ago
From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001
From: John Crispin <john@phrozen.org>
Date: Thu, 9 Mar 2017 11:03:18 +0100
Subject: [PATCH 69/69] arm: boot: add dts files
Signed-off-by: John Crispin <john@phrozen.org>
---
arch/arm/boot/dts/Makefile | 8 ++++++++
1 file changed, 8 insertions(+)
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
ipq40xx: add support for ASUS Lyra SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 years ago
@@ -785,11 +785,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
6 years ago
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
+ qcom-ipq4018-a42.dtb \
ipq40xx: add support for Linksys EA6350v3 Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com> [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 years ago
+ qcom-ipq4018-ea6350v3.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
6 years ago
+ qcom-ipq4018-eap1300.dtb \
+ qcom-ipq4018-ex6100v2.dtb \
+ qcom-ipq4018-ex6150v2.dtb \
+ qcom-ipq4018-fritz4040.dtb \
+ qcom-ipq4018-jalapeno.dtb \
+ qcom-ipq4018-nbg6617.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
+ qcom-ipq4018-wre6606.dtb \
qcom-ipq4019-ap.dk01.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c1.dtb \
qcom-ipq4019-ap.dk04.1-c3.dtb \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
+ qcom-ipq4019-a62.dtb \
ipq40xx: add support for ASUS Lyra SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 years ago
+ qcom-ipq4019-map-ac2200.dtb \
ipq40xx: Add patches for 4.19 This adds the necessary patches for 4.19 kernel. Upstreamed patches were dropped, backported upstreamed patches from 4.20. Drop Winbond ID patch since that NAND IC was upstreamed to use SPI-NAND framework and support for it was backported from 4.20. Rework ESSEDMA patches to compile under 4.19 due to timer changes, Clément Péron did the hard work and his changes were taken from the initial 4.19 PR. MR33 changes had to be manually refreshed to apply. Refresh other patches to apply. Signed-off-by: Robert Marko <robimarko@gmail.com> Remove
6 years ago
+ qcom-ipq4028-wpj428.dtb \
+ qcom-ipq4029-gl-b1300.dtb \
+ qcom-ipq4029-mr33.dtb \
qcom-ipq8064-ap148.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \