You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
openwrt/target/linux/lantiq/dts/ALL0333CJ.dts

120 lines
2.0 KiB
Plaintext

lantiq: add Allnet ALL0333CJ support This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ. Specifications: - SoC: Amazon-SE - RAM: 16MB - Storage: 4MB NOR FLash - LEDs: Power, Ethernet, DSL (Sync) - Buttons: 1x Reset Button (not currently supported, will be done) - 1x Ethernet-Port: 1x RJ45 10/100BaseTX - 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+) Installation: - can be done via telnet+tftp or serial console - default passwords: - via telnet (root:admin) - via webinterface http://172.16.1.254:8235/ (admin:coolwhite) Installation via telnet / tftp: host: # your own host must have an tftpd daemon, then do this: host: ifconfig eth0:172 172.16.1.1 up host: # telnet to allnet modem, root:admin host: telnet 172.16.1.254 modem: # kill this daemon, it spams your console modem: killall dsl_cpe_control modem: # change to some place in ram: modem: cd /ramdisk/tftp_upload modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage modem: tftp -g -r uImage 172.16.1.1 modem: # load these extra tools from your tftpd via: modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz modem: tftp -g -r flashwrite 172.16.1.1 modem: tftp -g -r fw_setenv 172.16.1.1 modem: tftp -g -r fw.conf 172.16.1.1 modem: ln -s fw_setenv fw_printenv modem: chmod +x * modem: ./fw_setenv disable_recovery y modem: ./fw_setenv kernel_addr 0xb0010000 modem: ./flashwrite /dev/mtd/1 uImage 0 Installation via serial line at uboot: uboot: # erase everything exept bootloader uboot: protect on b0000000 +10000; protect on b03f0000 +10000 uboot: erase all uboot: # get new firmware via tftp: uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000 uboot: # copy to flash: uboot: cp.b 0x80100000 $(kernel_addr) $(filesize) uboot: # disable proprietary image checking: uboot: setenv disable_recovery=y; saveenv uboot: # reboot with LEDE ;) uboot: reset Ethernet works as expected, DSL syncronization does not work properly currently, I am working on this issue. Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
7 years ago
/dts-v1/;
#include "amazonse.dtsi"
/ {
model = "ALL0333CJ - Allnet ALL0333CJ DSL Modem";
chosen {
bootargs = "console=ttyLTQ0,115200";
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-dsl = &dsl;
led-internet = &online_green;
};
};
memory@0 {
reg = <0x0 0x1000000>;
};
fpi@b0000000 {
etop@E180000 {
phy-mode = "mii";
};
};
fpi@10000000 {
gpio: pinmux@E100B10 {
pinctrl-names = "default";
pinctrl-0 = <&state_default>;
state_default: pinmux {
asc {
lantiq,groups = "asc";
lantiq,function = "asc";
};
keys_in {
lantiq,pins = "io0",/* "io25", */"io29";
lantiq,pull = <2>;
lantiq,open-drain = <1>;
};
};
};
localbus@0 {
nor-boot@0 {
compatible = "lantiq,nor";
bank-width = <2>;
reg = <0 0x0 0x400000>;
#address-cells = <1>;
#size-cells = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "uboot";
reg = <0x00000 0x10000>;
read-only;
};
partition@10000 {
label = "firmware";
reg = <0x10000 0x3ef200>;
};
partition@3ff200 {
label = "uboot_env";
reg = <0x3ff200 0xc00>;
read-only;
};
partition@3ffe00 {
label = "dummy_bits";
reg = <0x3ffe00 0x200>;
read-only;
};
};
};
};
};
gpio-leds {
compatible = "gpio-leds";
/* power led: red=off, green=on */
power: power {
label = "all0333cj:green:power";
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
lan: lan {
label = "all0333cj:green:lan";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
dsl: dsl {
label = "all0333cj:green:dsl";
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
};
online_green: online {
label = "all0333cj:green:online";
gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
};
online_red {
label = "all0333cj:red:online";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
};
};
};