You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
openwrt/target/linux/ramips/dts/mt7620a_asus_rt-ac54u.dts

63 lines
1.1 KiB
Plaintext

ramips: add support for ASUS RT-AC54U Specification: - CPU: MTK MT7620A - RAM: 64MB - ROM: 16MB SPI Flash Macronix MX25L12835E - WiFi1: MediaTek MT7620A - WiFi2: MediaTek MT7612E - Button: reset, wps - LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN - Ethernet: 5 ports, 4 LAN + 1 WAN - Other: 1x UART 1x USB2.0 Installation: Update using ASUS Firmware Restoration Tool: 1. Download the ASUS Firmware Restoration Tool but don't open it yet 2. Unplug your computer from the router 3. Put the router into Rescue Mode by: turning the power off, using a pin to press and hold the reset button, then turning the router back on while keeping the reset button pressed for ~5 secs until the power LED starts flashing slowly (which indicates the router has entered Rescue Mode) 4. Important (if you don't do this next step the Asus Firmware Restoration Tool will wrongly assume that the router is not in Rescue Mode and will refuse to flash it): go to the Windows Control Panel and temporarily disable ALL other network adapters except the one you will use to connect your computer to the router 5. For the single adapter you left enabled, temporarily give it the static IP 192.168.1.10 and the subnet mask 255.255.255.0 6. Connect a LAN cable between your computer (make sure to use the Ethernet port of the adapter you've just set up) and port 1 of the router (not the router's WAN port) 7. Rename sysupgrade.bin to factory.trx 8. Open the Asus Firmware Restoration Tool, locate factory.trx and click upload (if Windows shows a compatibility prompt, confirm that the tool worked fine) 9. Flashing and reboot is finished when the power LED stops blinking and stays on MAC assignment based on vendor firmware: 2g 0x4 label 5g 0x8004 label +4 lan 0x22 label +4 wan 0x28 label Signed-off-by: Zhijun You <hujy652@gmail.com> [rebased due to DTSI patch, minor commit message adjustments, fix label MAC address (lan->wan), do spi frequency increase separately] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 years ago
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7620a_asus_rt-ac5x.dtsi"
/ {
compatible = "asus,rt-ac54u", "ralink,mt7620a-soc";
model = "Asus RT-AC54U";
aliases {
label-mac-device = &ethernet;
ramips: add support for ASUS RT-AC54U Specification: - CPU: MTK MT7620A - RAM: 64MB - ROM: 16MB SPI Flash Macronix MX25L12835E - WiFi1: MediaTek MT7620A - WiFi2: MediaTek MT7612E - Button: reset, wps - LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN - Ethernet: 5 ports, 4 LAN + 1 WAN - Other: 1x UART 1x USB2.0 Installation: Update using ASUS Firmware Restoration Tool: 1. Download the ASUS Firmware Restoration Tool but don't open it yet 2. Unplug your computer from the router 3. Put the router into Rescue Mode by: turning the power off, using a pin to press and hold the reset button, then turning the router back on while keeping the reset button pressed for ~5 secs until the power LED starts flashing slowly (which indicates the router has entered Rescue Mode) 4. Important (if you don't do this next step the Asus Firmware Restoration Tool will wrongly assume that the router is not in Rescue Mode and will refuse to flash it): go to the Windows Control Panel and temporarily disable ALL other network adapters except the one you will use to connect your computer to the router 5. For the single adapter you left enabled, temporarily give it the static IP 192.168.1.10 and the subnet mask 255.255.255.0 6. Connect a LAN cable between your computer (make sure to use the Ethernet port of the adapter you've just set up) and port 1 of the router (not the router's WAN port) 7. Rename sysupgrade.bin to factory.trx 8. Open the Asus Firmware Restoration Tool, locate factory.trx and click upload (if Windows shows a compatibility prompt, confirm that the tool worked fine) 9. Flashing and reboot is finished when the power LED stops blinking and stays on MAC assignment based on vendor firmware: 2g 0x4 label 5g 0x8004 label +4 lan 0x22 label +4 wan 0x28 label Signed-off-by: Zhijun You <hujy652@gmail.com> [rebased due to DTSI patch, minor commit message adjustments, fix label MAC address (lan->wan), do spi frequency increase separately] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 years ago
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
leds {
compatible = "gpio-leds";
led_power: power {
label = "rt-ac54u:blue:power";
gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
};
usb {
label = "rt-ac54u:blue:usb";
gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
trigger-sources = <&ohci_port1>, <&ehci_port1>;
linux,default-trigger = "usbport";
};
wifi2g {
label = "rt-ac54u:blue:wifi2g";
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
};
};
&ethernet {
mtd-mac-address = <&factory 0x28>;
ramips: add support for ASUS RT-AC54U Specification: - CPU: MTK MT7620A - RAM: 64MB - ROM: 16MB SPI Flash Macronix MX25L12835E - WiFi1: MediaTek MT7620A - WiFi2: MediaTek MT7612E - Button: reset, wps - LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN - Ethernet: 5 ports, 4 LAN + 1 WAN - Other: 1x UART 1x USB2.0 Installation: Update using ASUS Firmware Restoration Tool: 1. Download the ASUS Firmware Restoration Tool but don't open it yet 2. Unplug your computer from the router 3. Put the router into Rescue Mode by: turning the power off, using a pin to press and hold the reset button, then turning the router back on while keeping the reset button pressed for ~5 secs until the power LED starts flashing slowly (which indicates the router has entered Rescue Mode) 4. Important (if you don't do this next step the Asus Firmware Restoration Tool will wrongly assume that the router is not in Rescue Mode and will refuse to flash it): go to the Windows Control Panel and temporarily disable ALL other network adapters except the one you will use to connect your computer to the router 5. For the single adapter you left enabled, temporarily give it the static IP 192.168.1.10 and the subnet mask 255.255.255.0 6. Connect a LAN cable between your computer (make sure to use the Ethernet port of the adapter you've just set up) and port 1 of the router (not the router's WAN port) 7. Rename sysupgrade.bin to factory.trx 8. Open the Asus Firmware Restoration Tool, locate factory.trx and click upload (if Windows shows a compatibility prompt, confirm that the tool worked fine) 9. Flashing and reboot is finished when the power LED stops blinking and stays on MAC assignment based on vendor firmware: 2g 0x4 label 5g 0x8004 label +4 lan 0x22 label +4 wan 0x28 label Signed-off-by: Zhijun You <hujy652@gmail.com> [rebased due to DTSI patch, minor commit message adjustments, fix label MAC address (lan->wan), do spi frequency increase separately] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 years ago
};
&state_default {
gpio {
groups = "i2c", "wled", "uartf";
function = "gpio";
};
};
&pcie0 {
wifi@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x8000>;
ieee80211-freq-limit = <5000000 6000000>;
led {
led-sources = <2>;
};
};
};