openwrt/target/linux/kirkwood/base-files/etc/board.d/01_leds

#!/bin/sh
#
# Copyright (C) 2012-2015 OpenWrt.org
#

. /lib/functions/uci-defaults.sh

board_config_update

board=$(board_name)

case "$board" in
iom,ix2-200)
	ucidef_set_led_timer "health" "health" "status:white:rebuild_led" "200" "800"
	;;
linksys,e4200-v2|\
linksys,ea4500)
	ucidef_set_led_default "pulse" "pulse" "viper:white:pulse" "1"
	;;
esac

board_config_flush

exit 0
kirkwood: use uci-defaults to configure different boards Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> SVN-Revision: 31990 12 years ago			`#!/bin/sh`
			`#`
kirkwood: switch from uci-defaults to board.d Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47733 9 years ago			`# Copyright (C) 2012-2015 OpenWrt.org`
kirkwood: use uci-defaults to configure different boards Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> SVN-Revision: 31990 12 years ago			`#`

all: drop old uci-defaults.sh Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867 9 years ago			`. /lib/functions/uci-defaults.sh`
kirkwood: use uci-defaults to configure different boards Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> SVN-Revision: 31990 12 years ago
kirkwood: switch from uci-defaults to board.d Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47733 9 years ago			`board_config_update`

treewide: use the generic board_name function Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me> 7 years ago			`board=$(board_name)`
kirkwood: base-files: use /lib/functions/kirkwood.sh Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 41336 10 years ago
			`case "$board" in`
kirkwood: use real model names for Linksys devices This replaces the internal device names "Audi" and "Viper" with the real model names, which a user would look for. This makes the Linksys devices on this target consistent with the names recently changed for mvebu based on the same idea. As a consequence, the "viper" device definition is split into two separate definitions with the correct names for both real models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 4 years ago			`iom,ix2-200)`
kirkwood: add support for Iomega Storcenter ix2-200 Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com> 6 years ago			`ucidef_set_led_timer "health" "health" "status:white:rebuild_led" "200" "800"`
			`;;`
kirkwood: use real model names for Linksys devices This replaces the internal device names "Audi" and "Viper" with the real model names, which a user would look for. This makes the Linksys devices on this target consistent with the names recently changed for mvebu based on the same idea. As a consequence, the "viper" device definition is split into two separate definitions with the correct names for both real models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> 4 years ago			`linksys,e4200-v2\|\`
			`linksys,ea4500)`
kirkwood: consistently use engineering board names Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47430 9 years ago			`ucidef_set_led_default "pulse" "pulse" "viper:white:pulse" "1"`
kirkwood: add support for Linksys EA4500 Support is added only for kernel 3.14 - do not show it until the switch is made. Following uboot env changes are needed to make it work on stock uboot: 10 years ago			`;;`
kirkwood: use uci-defaults to configure different boards Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> SVN-Revision: 31990 12 years ago			`esac`

kirkwood: switch from uci-defaults to board.d Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47733 9 years ago			`board_config_flush`
kirkwood: use uci-defaults to configure different boards Signed-off-by: Luka Perkov <openwrt@lukaperkov.net> SVN-Revision: 31990 12 years ago
			`exit 0`