You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

53 lines
1.8 KiB
Plaintext

#!/bin/sh
#
# Copyright (C) 2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
board_config_update
board=$(board_name)
boardname="${board##*,}"
case "$board" in
tplink,c2600)
ucidef_set_led_usbport "usb1" "USB 1" "${boardname}:white:usb_2" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB 2" "${boardname}:white:usb_4" "usb3-port1" "usb4-port1"
ucidef_set_led_switch "wan" "wan" "${boardname}:white:wan" "switch0" "0x20"
ucidef_set_led_switch "lan" "lan" "${boardname}:white:lan" "switch0" "0x1e"
;;
netgear,d7800 |\
netgear,r7500 |\
netgear,r7500v2 |\
netgear,r7800)
ucidef_set_led_usbport "usb1" "USB 1" "${boardname}:white:usb1" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB 2" "${boardname}:white:usb2" "usb3-port1" "usb4-port1"
ucidef_set_led_netdev "wan" "WAN" "${boardname}:white:wan" "eth0"
ucidef_set_led_ide "esata" "eSATA" "${boardname}:white:esata"
;;
avm,fritzbox-4040)
ucidef_set_led_wlan "wlan" "WLAN" "fritz4040:green:wlan" "phy0tpt" "phy1tpt"
ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
7 years ago
;;
zyxel,nbg6817)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:amber:wifi2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:amber:wifi5g" "phy0tpt"
ucidef_set_led_netdev "wan" "WAN" "${boardname}:white:internet" "eth1"
;;
tplink,vr2600v)
ucidef_set_led_usbport "usb" "USB" "${boardname}:white:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
ucidef_set_led_switch "lan" "lan" "${boardname}:white:lan" "switch0" "0x1e"
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:white:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:white:wlan5g" "phy1tpt"
ucidef_set_led_switch "wan" "wan" "${boardname}:white:wan" "switch0" "0x20"
;;
*)
;;
esac
board_config_flush
exit 0