You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
openwrt/target/linux/mpc85xx/patches-4.19/106-powerpc-85xx-ws-ap3710i...

31 lines
1.0 KiB
Diff

mpc85xx: add support for Enterasys WS-AP3710i Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
4 years ago
--- a/arch/powerpc/platforms/85xx/Kconfig
+++ b/arch/powerpc/platforms/85xx/Kconfig
@@ -71,6 +71,17 @@ config PANDA
This board is a Concurrent Dual-Band wireless access point with a
Freescale P1020 SoC.
+config WS_AP3710I
+ bool "Enterasys WS-AP3710i"
+ select DEFAULT_UIMAGE
+ select ARCH_REQUIRE_GPIOLIB
+ select GPIO_MPC8XXX
+ help
+ This option enables support for the Enterasys WS-AP3710i board.
+
+ This board is a Concurrent Dual-Band wireless access point with a
+ Freescale P1020 SoC.
+
config MPC8540_ADS
bool "Freescale MPC8540 ADS"
select DEFAULT_UIMAGE
--- a/arch/powerpc/platforms/85xx/Makefile
+++ b/arch/powerpc/platforms/85xx/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
obj-$(CONFIG_PANDA) += panda.o
obj-$(CONFIG_TWR_P102x) += twr_p102x.o
+obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o