dumalogiya
/
openwrt
2
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
v19.07.3_mercusys_ac12_duma
master
Branches Tags
${ item.name }
Create tag ${ searchTerm }
Create branch ${ searchTerm }
from '16b01fb1b9'
${ noResults }
openwrt/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac

29 lines
530 B
Plaintext
Raw Normal View History Unescape Escape

mpc85xx: add support for Sophos RED 15w Rev.1 Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 years ago
#!/bin/ash
[ "$ACTION" == "add" ] || exit 0
PHYNBR=${DEVPATH##*/phy}
[ -n $PHYNBR ] || exit 0
. /lib/functions.sh
. /lib/functions/system.sh
board=$(board_name)
case "$board" in
mpc85xx: add support for Enterasys WS-AP3710i Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
4 years ago
enterasys,ws-ap3710i)
echo $(mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR}) > /sys${DEVPATH}/macaddress
;;
mpc85xx: add support for OCEDO Panda CPU: FSL P1020 (2x 800MHz E500 PPC) RAM: 1GB DDR3 FLASH: 256MiB NAND WiFi: 2x Atheros AR9382 2x2:2 abgn ETH: 2x BCM54616S - 1x BCM53128 8-port switch LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS) BTN: 1x RESET Installation ------------ 1. Download initrams kernel image, dtb binary and sysupgrade image. 2. Place initramfs kernel into tftp root directory. Rename to "panda-uimage-factory". 3. Place dtb binary into tftp root directory. Rename to "panda.fdt". 4. Start tftp server on 192.168.100.8/24. 5. Power up the device with the reset button pressed. It will download the initrams and dtb via tftp and boot into OpenWRT in RAM. 6. SSH into the device and remove the factory partitions. > ubirmvol /dev/ubi0 --name=kernel1 > ubirmvol /dev/ubi0 --name=rootfs1 > ubirmvol /dev/ubi0 --name=devicetree1 You will have around 60 MiB of free space with that. You can also delete "kernel2", "devicetree2", "rootfs2" and "storage" respectively in case you do not want to go back to the vendor firmware. 7. Modify the U-Boot bootcmd to allow for booting OpenWRT > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel && bootm 0x1000000" > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200 ubi.mtd=3,2048" > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt" 8. Transfer the sysupgrade image via scp into the /tmp directory. 9. Upgrade the device > sysupgrade -n /tmp/<imagename> Signed-off-by: David Bauer <mail@david-bauer.net>
5 years ago
ocedo,panda)
WMAC=wmac$(($PHYNBR + 1))
MAC=$(mtd_get_mac_ascii uboot-env0 ${WMAC})
echo ${MAC} > /sys${DEVPATH}/macaddress
;;
mpc85xx: add support for Sophos RED 15w Rev.1 Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 years ago
sophos,red-15w-rev1)
echo $(mtd_get_mac_ascii u-boot-env ethaddr) > /sys${DEVPATH}/macaddress
;;
*)
;;
esac